|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
MOTOROLA SEMICONDUCTOR TECHNICAL DATA Order this document by MBRP30060CT/D Designer'sTM Data Sheet SWITCHMODETM Schottky Power Rectifier POWERTAPTM II Package . . . employing the Schottky Barrier principle in a large area metal-to-silicon power diode. State of the art geometry features epitaxial construction with oxide passivation and metal overlay contact. Ideally suited for low voltage, high frequency switching power supplies, free wheeling diode and polarity protection diodes. * Highly Stable Oxide Passivated Junction * Guardring for Stress Protection * Matched dual die construction - May be Paralleled for High Current Output * High dv/dt Capability * Very Low Forward Voltage Drop Mechanical Characteristics: * Case: Epoxy, Molded with Metal Heatsink Base * Weight: 80 grams (approximately) * Finish: All External Surfaces Corrosion Resistant * Base Plate Torques: See procedure given in the Package Outline Section * Top Terminal Torque: 70 in- lb max. * Shipped 25 units per foam * Marking: MBRP30060CT MAXIMUM RATINGS Rating Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage Average Rectified Forward Current (At Rated VR, TC = 88C) Peak Repetitive Forward Current (At Rated VR, Square Wave, 20 kHz, TC = 92C) Per Leg Per Package Per Leg Symbol VRRM VRWM VR IO IFRM IFSM Tstg, TC TJ dv/dt MBRP30060CT SCHOTTKY BARRIER RECTIFIER 300 AMPERES 60 VOLTS 1 2 3 CASE 357C- 03 POWERTAP II Value 60 Unit Volts 150 300 300 2500 - 55 to +150 - 55 to +150 1000 Amps Amps Amps C C V/s C/W Non-Repetitive Peak Surge Current Per Package (Surge applied at rated load conditions, halfwave, single phase, 60 Hz) Storage/Operating Case Temperature Operating Junction Temperature Voltage Rate of Change (Rated VR, TJ = 25C) THERMAL CHARACTERISTICS Thermal Resistance -- Junction-to-Case Per Leg Rtjc 0.46 ELECTRICAL CHARACTERISTICS Maximum Instantaneous Forward Voltage (1), see Figure 2 (IF = 150 A) (IF = 300 A) Maximum Instantaneous Reverse Current, see Figure 4 (VR = 60 V) (VR = 30 V) (1) Pulse Test: Pulse Width 250 s, Duty Cycle 2%. POWERTAP and SWITCHMODE are trademarks of Motorola, Inc. This document contains information on a product under development. Motorola reserves the right to change or discontinue this product without notice. Per Leg VF TJ = 25C 0.85 0.97 TJ = 25C 0.80 0.32 TJ = 100C 0.75 0.87 TJ = 100C 100 60 Volts Per Leg IR mA (c) Motorola Schottky Power Rectifier Data Motorola, Inc. 1995 1 MBRP30060CT I F , INSTANTANEOUS FORWARD CURRENT (AMPS) 1E+3 I F , INSTANTANEOUS FORWARD CURRENT (AMPS) 1E+3 1E+2 TJ = 150C 1E+2 TJ = 150C 1E+1 TJ = 25C TJ = 100C 1E+0 0.6 0.8 1.0 0.2 0.4 VF, MAXIMUM INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 1E+1 TJ = 25C TJ = 100C 1E+0 0.1 0.3 0.5 0.7 VF, INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 0.9 Figure 1. Typical Forward Voltage Figure 2. Maximum Forward Voltage 1E - 1 1E - 2 1E - 3 TJ = 150C I R , MAXIMUM REVERSE CURRENT (AMPS) 1E+0 I R , REVERSE CURRENT (AMPS) 1E+0 1E - 1 TJ = 100C TJ = 100C 1E - 4 1E - 5 TJ = 25C 1E - 6 0 10 20 30 40 VR, REVERSE VOLTAGE (VOLTS) 50 60 1E - 2 1E - 3 TJ = 25C 1E - 4 0 10 20 30 40 VR, REVERSE VOLTAGE (VOLTS) 50 60 Figure 3. Typical Reverse Current Figure 4. Maximum Reverse Current I O , AVERAGE FORWARD CURRENT (AMPS) 250 dc 200 SQUARE WAVE Ipk/Io = p Ipk/Io = 5 Ipk/Io = 10 50 Ipk/Io = 20 FREQ = 20 kHz P FO , AVERAGE POWER DISSIPATION (WATTS) 180 160 140 120 100 80 60 40 20 0 0 TJ = 150C 50 100 200 150 IO, AVERAGE FORWARD CURRENT (AMPS) 250 Ipk/Io = 10 Ipk/Io = 20 Ipk/Io = p Ipk/Io = 5 SQUARE WAVE dc 150 100 0 0 20 120 40 60 80 100 TC, CASE TEMPERATURE (C) 140 160 Figure 5. Current Derating (PER LEG) Figure 6. Forward Power Dissipation (PER LEG) 2 Motorola Schottky Power Rectifier Data MBRP30060CT 2200 TJ = 25C C, CAPACITANCE (pF) 1800 1400 1000 10 15 20 25 30 35 40 45 50 VR, REVERSE VOLTAGE (VOLTS) 55 60 Figure 7. Capacitance R(T) , TRANSIENT THERMAL RESISTANCE (NORMALIZED) 1E+0 1E-1 Rtjc(t) = Rtjc*r(t) 1E- 2 1E- 5 1E- 4 1E- 3 1E- 2 t, TIME (s) 1E-1 1E+0 1E+1 1E+2 Figure 8. Thermal Response VCC 12 Vdc + 150 V, 10 mAdc 12 V 100 2 ms 1 kHz 2N2222 CURRENT AMPLITUDE ADJUST 0 -10 AMPS 100 W CARBON 2N6277 2 kW D.U.T. 4 mF + 1 CARBON 1N5817 Figure 9. Test Circuit for Repetitive Reverse Current Motorola Schottky Power Rectifier Data 3 MBRP30060CT MAXIMUM MECHANICAL RATINGS Terminal Penetration: Terminal Torque: Mounting Torque -- Outside Holes: Mounting Torque -- Center Hole: Seating Plane Flatness 0.235 max 70 in-lb max 70 in-lb max 8-10 in-lb max 1 mil per in. (between mounting holes) POWERTAP MECHANICAL DATA APPLIES OVER OPERATING TEMPERATURE 2 Vertical Pull 250 lbs. max 2 in. Lever Pull 50 lbs. max Note: While the POWERTAP is capable of sustaining these vertical and levered tensions, the intimate contact Note: between POWERTAP and heat sink may be lost. This could lead to thermal runaway. The use of very Note: flexible leads is recommended for the anode connections. Use of thermal grease is highly recommended. MOUNTING PROCEDURE The POWERTAP package requires special mounting considerations because of the long longitudinal axis of the copper heat sink. It is important to follow the proper tightening sequence to avoid warping the heat sink, which can reduce thermal contact between the POWERTAP and heat sink. STEP 1: Locate the POWERTAP on the heat sink and start mounting bolts into the threads by hand (2 or 3 turns). 2 - 3 TURNS 2 - 3 TURNS 2 - 3 TURNS POWER TAP HEAT SINK STEP 2: Finger tighten the center bolt. The bolt may catch on the threads of the heat sink so it is important to make sure the face of the bolt or washer is in contact with the surface of the POWERTAP. STEP 3: Tighten each of the end bolts between 5 to 10 in-lb. 2 - 3 TURNS FINGER-TIGHT 2 - 3 TURNS POWER TAP HEAT SINK 5 - 10 IN-LB FINGER-TIGHT 5 - 10 IN-LB POWER TAP HEAT SINK STEP 4: Tighten the center bolt between 8 to 10 in-lb. 5 - 10 IN-LB 8 - 10 IN-LB 5 - 10 IN-LB POWER TAP HEAT SINK STEP 5: Finally, tighten the end bolts to 70 in-lb. 70 IN-LB 8 - 10 IN-LB 70 IN-LB POWER TAP HEAT SINK 4 Motorola Schottky Power Rectifier Data MBRP30060CT PACKAGE DIMENSIONS -AR G -B- W 0.25 (0.010) N M TA M B M NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. TERMINAL PENETRATION: 5.97 (0.235) MAXIMUM. INCHES MIN MAX 3.450 3.635 0.700 0.810 0.615 0.640 0.120 0.130 0.435 0.445 1.370 1.380 0.007 0.030 1/4-20UNC 2B 0.270 0.285 31.50 BSC 0.600 0.630 0.330 0.375 0.170 0.190 MILLIMETERS MIN MAX 87.63 92.33 17.78 20.57 15.53 16.26 3.05 3.30 11.05 11.30 34.80 35.05 0.18 0.76 1/4-20UNC 2B 6.86 7.32 80.01 BSC 15.24 16.00 8.39 9.52 4.32 4.82 Q H F 2 PL 0.25 (0.010) M TA M B M C U V -TE SEATING PLANE DIM A B C E F G H N Q R U V W CASE 357C-03 ISSUE C Motorola Schottky Power Rectifier Data 5 MBRP30060CT Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters can and do vary in different applications. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE (602) 244-6609 INTERNET: http://Design-NET.com JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, Toshikatsu Otsuki, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-3521-8315 HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 6 *MBRP30060CT/D* Motorola Schottky Power Rectifier Data MBRP30060CT/D |
Price & Availability of MBRP30060CTD |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |